Digital Monitoring XR5 Guia de Instalação descarregar pdf (Página 14)

Page 10

Installation

2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282

XR5FC/XR5SL Installation Guide

11.3 Zone response time

A condition must be present on the zone for at least

500 milliseconds before it is detected by the XR5FC

and XR5SL panels. Ensure detection devices used on

the zones are rated for use with this delay.

11.4 Compatible 2-wire smoke detectors

The table to the right lists those detectors meeting the

compatibility requirements for use with the Class B

(Stlyle A) zones on the XR5FC and XR5SL fire

panels.

Do not mix detectors from different manufacturers on

the same zone.

Form C Relay Outputs

12.1 Description

The XR5FC and XR5SL panels can provide two auxiliary Form C (SPDT) relays when equipped with DMP

Model 305 Plug-in Relays in sockets OUTPUT 1 and OUTPUT 2. Each relay is rated for 1 Amp at 30 VDC.

Each output provides one Common, one Normally Open, and one Normally Closed terminal. Field wiring for the

Form C relays connects to the 6-position terminal strip on the lower right corner of the XR5FC and XR5SL

boards.

The Form C relays can be operated by any of the functions listed below:

1) Activation by a zone condition

2) Communication Failure

3) Fire alarm or Fire trouble

Annunciator Outputs

13.1 Description

The XR5FC and XR5SL panels provide four open collector annunciator outputs that can be programmed to

indicate the activity of the panel's zones or conditions occurring on the system. Open collector outputs do not

provide a voltage but instead switch to ground voltage from another source. Each annunciator output is

rated for 50mA at 30 VDC resistive.

Form C and Annunciator outputs operate together:

The Form C outputs 1 and 2 are internally connected to

the Annunciator outputs 1 and 2. Any options assigned to Output 1 or 2 in the panel's Output Options

programming applies to both outputs. While the Form C outputs each require a Model 305 Plug-in Relay, the

annunciator outputs will work without the relays.

The Annunciator outputs can respond to any of the conditions listed below:

1) Activation by zone condition

2) Communication failure

3) Fire Alarm or Fire Trouble

13.2 Harness wiring

The Annunciator outputs are accessible by installing the DMP 300 Harness on the 4-pin header labeled J12.

The output locations are shown below:

Output Color Wire

1 Red 1

2 Yellow 2

3 Green 3

4 Black 4

Devices connected to the outputs must be located within the same room as the XR5FC and XR5SL panels.

Figure 6: Compatible 2-wire smoke detectors

ekaMledoMrotceteD

esaBesaB

fo#

srotceteD

smetsySnoitceteD282SDB enoNA/N01

smetsySnoitceteDHT282SDB enoNA/N01

smetsySnoitceteD052SDB LW2BM,W2BMA01

smetsySnoitceteDHT052SDB LW2BM,W2BMA01

smetsySnoitceteDDH052SDB LW2BM,W2BMA01

LSE/lortneSTA924A90SenoNA/N21

ikihcoH538-KLS5-DHN002-BSH,002-BSH55-BH7

ikihcoHH538-KLS5-DHN002-BSH,002-BSH55-BH7

ikihcoH21-KLS4-DHN1-21-BSH,1-21-BSH08BH02

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 20 21 22

Comentários a estes Manuais

Sem comentários

Digital Monitoring XR5 Guia de Instalação Página 14

Comentários a estes Manuais

Manuais e produtos relacionados com Detetores de fumo Digital Monitoring XR5